How to use remote installation services

The client then logs on with a valid user account. The server must meet the minimum hardware requirements for the version of Windows Server that is installed. SCSI-based disk controllers and disks are preferred. RIS requires a lot of disk space, and you cannot install it on the same drive or partition on which Windows Server is installed. Make sure that the chosen drive contains enough free disk space for at least one full set of the installation files for the operating system you plan to remotely install.

The following list describes the minimum hardware that is required for RIS client computers:. Several network services must be active and available for RIS.

You can install the following services either on the RIS server or on other servers that are available on the network:. Make sure that the client computer's network adapter has been set as the primary boot device in the computer BIOS.

If the network adapter is configured as the primary boot device, the client requests a network service boot from the RIS server on the network when the client starts.

Do not press F12 unless you need a new operating system installation or access to maintenance and troubleshooting tools. After the client operating system has been installed by using RIS, you can ignore the prompt to press F12 during future client computer startups.

To use the remote boot disk to start the installation, insert the boot disk into the floppy disk drive, and then start the client computer. The floppy disk drive must be set as the primary boot device in the client BIOS. After the computer starts from the disk, you are prompted to press F12 to start the network service boot process. You must remove the boot disk after you press F12 and before the text-mode portion of the operating system installation completes.

In this case, you must press F12 on the Compaq startup screen, and then press F12 again when you are prompted by the RIS server. Click to select the Remote Installation Services check box, and then click Next. After you do so, you may receive a message with options for upgrading the operating system.

Click No. Type the drive letter and folder in which the RIS files are stored, and then click Next. Respond to client computers requesting service. If you select this option, RIS is enabled, and it will respond to client computers that are requesting service.

Do not respond to unknown client computers. Remote Installation Services. Configure Your Network Securely from the Start! Proven Three-Phase Plan During a remote installation session, an experienced WatchGuard technician works with you over the phone to get your appliance configured correctly. Phase 1: Preparation Before beginning the remote session, you will be asked to complete a questionnaire.

Phase 3: Sign Off Finally, before you sign-off on the project, the technician will review the configuration to ensure that the goals outlined in the preparation phase have been achieved. Contact Support Cost Please contact your reseller for price and licensing options. When you create a standard deployment of Remote Desktop Services, the Remote Desktop Connection Broker role service provides access to the complete functionality of Remote Desktop Services.

Because a configuration without the RD Connection Broker role service does not provide access to all RDS functionality, you should use such a configuration only if there is no other option. You can use the instructions in this article to configure RDS service by using a single server either a member of a workgroup or a domain controller DC. The process of deploying RDS service roles on a single workgroup server or DC differs from that of deploying a standard RDS configuration on multiple computers.

To do this, follow these steps:. If you have to manage group memberships manually, the Terminal Server License Servers group is located in the Built-in container in Active Directory Users and Computers.

If you are using a workgroup server, you must use per-device CALs. Add the users that you want to allow to connect to the Remote Desktop Users group.

To do this, use the following tools:. Change the local policy of the computer to add your remote desktop users to the Allow logon through Remote Desktop Services local policy object.

If you are using a workgroup server, you must use 2. You should see the RDS licensing server name in the output. After you finish this step, users can start remote desktop sessions by using any supported RDS client.

Windows 10 can be configured to access your computer using Remote Desktop from a number of different devices. Allowing Remote Desktop sessions to your computer from your remote devices gives you access to files and resources from anywhere you are when away from home or the office. The remote installation of the service which you can do with sc. Stack Overflow for Teams — Collaborate and share knowledge with a private group.

Create a free Team What is Teams? Collectives on Stack Overflow. Learn more. Installing services remotely Ask Question. Asked 11 years, 6 months ago. Active 11 years, 6 months ago. Viewed 3k times. I'm currently using a method similar to the one discussed here: How to install a windows service programmatically in C?